Skip to content
← All guides
MechanicalUpdated November 14, 2026· 11 min read

What a Commercial Kitchen Hood and Fire Suppression Cost

A Type 1 hood is rarely one line in a budget. It is a hood, welded duct, an exhaust fan, a make-up air unit, a UL 300 suppression system, structural support and a balance report — and on a restaurant fit-out it is usually the largest single mechanical cost. Here is what each part runs, what the two codes require, and why an inherited hood is worth less than it looks.

Reviewed by John Dogus, Founder & CEO

The short version

  • Budget the package, not the hood. In a typical single-line restaurant the whole installed system runs $50,000 to $95,000, roughly a tenth to a quarter of the buildout.
  • Two codes govern it. The Building Code says how it is installed, to NFPA 96, with suppression to UL 300. The Fire Code says how it is maintained, also to NFPA 96.
  • Make-up air is a second rooftop unit with its own gas, power and structure. It is the line most often missing from an early budget.
  • An existing exhaust system may be approved under the Fire Code, but a pre-UL 300 suppression system is not a system you can keep.
  • The only fixed frequency in Ontario law is a check every seven days. The cleaning interval itself comes from NFPA 96 and depends on how much you cook.
What each part of a Type 1 package costs installed — NHFC planning bands
  • Make-up air unit, with heating$12,000 – $35,000
  • Welded duct to the roof and the exhaust fan$8,000 – $30,000
  • Fire suppression system, UL 300$6,000 – $20,000
  • Structural support, curbs and roof penetrations$3,000 – $18,000
  • Gas and electrical for the fan and make-up air$4,000 – $15,000
  • Balancing, commissioning and the fire inspection$2,000 – $6,000
$0$36,980
View as table
CategoryLowHigh
Make-up air unit, with heating$12,000$35,000
Welded duct to the roof and the exhaust fan$8,000$30,000
Fire suppression system, UL 300$6,000$20,000
Structural support, curbs and roof penetrations$3,000$18,000
Gas and electrical for the fan and make-up air$4,000$15,000
Balancing, commissioning and the fire inspection$2,000$6,000

Ask what a kitchen hood costs and you will get answers between $15,000 and $150,000, because the question is being answered about different things. The stainless canopy over the cooking line is a minor purchase. The system it belongs to — welded duct to the roof, a fan sized to the hood, a second rooftop unit bringing tempered air back in, a suppression system engineered to your exact appliance positions, and the structure to carry all of it — is usually the largest single mechanical cost in a restaurant fit-out.

This guide prices the package. Commercial kitchen ventilation, explained covers how the system works and why each part exists; this one is about the money and the code behind it.

What you are actually buying

Part What it is
The hood The canopy and filters over the cooking line. Type 1 for grease-laden vapour, Type 2 for heat and steam only.
Welded grease duct The route from the hood to the roof. Welded, sealed, and fire-rated where it passes through construction.
Exhaust fan Sized to the hood’s exhaust volume, mounted on a curb on the roof.
Make-up air unit A second rooftop unit that heats and delivers replacement air for everything the hood removes.
Fire suppression A wet chemical system to UL 300, with nozzles positioned for your specific appliances, tied to gas shut-off and the alarm.
Structure and roof work Curbs, reinforcement and penetrations for two rooftop units.
Balancing and commissioning Measuring and adjusting exhaust against make-up air, and the report that proves it.

Only the first line is the thing most people picture, and it is typically about a fifth of the total.

What it costs

A Type 1 hood canopy itself runs $1,200 to $1,900 per linear foot installed, as an NHFC planning band — so a 12-foot cooking line is roughly $14,000 to $23,000 of hood. The chart at the top of this page gives the installed band for every other part of the package.

For a typical single cooking line in a restaurant, the whole installed package lands at $50,000 to $95,000.

Read those bands and this total together rather than adding the bands up. The high end of every line does not happen on one project: a long vertical duct run, structural reinforcement, a solid-fuel appliance and a difficult roof can stack to well past $150,000, but that is a hard site, not a typical one. If several of the drivers below apply to your space, price it properly before you sign anything.

Against the buildout range the cost calculator returns for a 2,400 sq ft restaurant renovation — $360,000 to $670,000 — a hood package at $50,000 to $95,000 is roughly a tenth to a quarter of the whole fit-out. That share is the useful number to carry into a feasibility conversation, because it scales with the project in a way a dollar figure does not.

These are planning bands from our own projects. Unlike permits and the liquor licence, where the issuing authority publishes a fee schedule you can check, nobody publishes hood prices. That is exactly why the answers online vary by a factor of ten, and it is why a real quote against real drawings is worth getting early.

For the equipment side of that quote, our equipment partner Norpex has a commercial kitchen hood builder. You line up your appliances, the hood sizes itself to the line, and a quote for the hood, the exhaust fan, the make-up air unit and the fire suppression comes back by email at no charge. The parts that depend on the building — the duct route, the structure and the roof — still need someone to look at the site and the drawings.

Two codes, not one

The hood sits under two regulations that people routinely conflate, and knowing which is which tells you who to ask.

The Building Code governs installation. All commercial cooking equipment has to be provided with ventilation systems designed, constructed and installed to conform to NFPA 96. Fire protection systems for commercial cooking equipment using vegetable oil or animal fat have to conform to ANSI/CAN/UL/ULC 300 or ULC/ORD-C1254.6. There is also a dimension worth checking before the duct route is fixed: the Building Code sets a minimum 3.0 m between a kitchen exhaust outlet and an outdoor air intake, which on a tight roof can decide where the fan goes and how long the run is.

The Fire Code governs operation and maintenance. A cooking operation producing smoke or grease-laden vapours has to be provided with an exhaust system and a fire protection system in accordance with NFPA 96, and those systems have to be maintained in accordance with NFPA 96. Instructions for operating the suppression system manually have to be posted conspicuously in the kitchen, and included in the fire safety plan where one is required.

In short: the building department signs off that it was built right, and the fire service checks for the rest of the restaurant’s life that it is being kept right.

The second-generation trap

A space with a hood already in it is a genuine asset — and the Fire Code is explicit that an existing exhaust or fire protection system may be approved. That word is doing a lot of work, though, and there are three ways an inherited system turns out to be worth less than the lease negotiation assumed.

It is the wrong type or the wrong size. A Type 2 hood over your fryer is not a discount, it is a code problem. A 10-foot hood over a 14-foot line is a shorter line or a second hood.

The suppression system predates UL 300. Older dry chemical systems were designed around the cooking oils and appliance types of an earlier era. The current standard is wet chemical to UL 300, and a pre-UL 300 system above a working cooking line is a replacement, not an inspection. This is the single most common unbudgeted surprise in a second-generation kitchen.

The duct is not where you need it, or not in the condition you assumed. Grease duct that has not been cleaned or inspected, a route that no longer suits your layout, or a landlord who will not permit a new roof penetration all turn an inherited asset into a partial one.

Three questions settle it before the lease: what type and length is the hood, when was the suppression system last serviced and does it meet UL 300, and has the duct been cleaned with the record to prove it. Choosing a space covers the rest of that inspection.

What moves the number most

The ventilation guide lists the mechanical drivers in order of impact. In money terms the three that most often blow a hood budget are:

  1. Distance to the roof. Duct run length is the clearest multiplier in the package. A ground-floor unit under its own roof is a different project from a unit on the first floor of a three-storey building, where the duct has to be boxed, rated and routed through somebody else’s space.
  2. Structural capacity. Two rooftop units need curbs and, often, reinforcement. This is rarely in a first budget and never cheap.
  3. Solid fuel. Wood or charcoal brings a separate duct system, spark arrest and its own cleaning regime, and it is the one menu decision that reliably changes the mechanical scope.

Two more worth pricing early: whether the gas and electrical services can actually carry a heated make-up air unit and an exhaust fan — see power and gas — and whether the landlord permits the roof penetrations at all.

What it costs to run

This is where most published advice is confidently wrong, because it quotes an interval that is not in Ontario law.

The one fixed frequency is weekly. The Fire Code requires that hoods, ducts and filters subject to accumulations of combustible deposits be checked at intervals not greater than seven days, and cleaned if the accumulation creates a fire hazard. That is a check by you, not a visit by a contractor.

The cleaning interval comes from NFPA 96, and it depends on your cooking. The Fire Code adopts NFPA 96 for maintenance rather than setting a number, and NFPA 96 scales inspection frequency to how much and what you cook. A charbroiler running all day and a bakery oven are not on the same schedule. Ask your service provider which category your operation falls into and get it in writing.

Keep the records. Where the Fire Code requires a measure to be carried out, a record has to be made noting what was done and the date and time it was done. The fire inspector will ask for the service record, and “we have it done regularly” is not one.

Budget $2,000 to $6,000 a year for cleaning and suppression service on a single-hood restaurant as an NHFC planning band, scaling with hood length, duct run and cooking volume. The costs that arrive after you open puts that beside the rest of the operating picture.

Where the budget usually goes wrong

  • The hood is priced and the package is not. A supplier quote for a canopy is not a system cost. Duct, fan, make-up air, suppression and structure are four to five times the hood.
  • Make-up air is discovered late. It is a second rooftop unit with its own gas, power and structure, and it is the line most often missing from an early number.
  • The layout changes after suppression is designed. Nozzles are positioned for specific appliances in specific places. Moving the fryer means re-engineering the system.
  • An inherited system is assumed to be compliant. A hood that exists is not a hood that passes.
  • Nobody checks the roof. Structural capacity and permission to penetrate are both assumptions until somebody confirms them.

Getting the hood right starts with the equipment layout being final, because every number above follows the appliance line. That coordination — drawings where the kitchen layout, the mechanical and the suppression design agree before anything is ordered — is the part that keeps this package from being the line that moves your opening date.

Requirements change and the authority having jurisdiction decides any specific project. Check each one for your address before you rely on anything here.

Sources

  • Ontario Building Code, O. Reg. 163/24 (the 2024 Building Code), Division B, Article 6.3.1.6. (commercial cooking equipment ventilation to NFPA 96), Article 6.9.1.3. (suppression to ANSI/CAN/UL/ULC 300 or ULC/ORD-C1254.6) and Table 6.3.2.9. (3.0 m from a kitchen exhaust outlet to an outdoor air intake): 2024 Building Code Compendium, Part 6
  • Fire Code, O. Reg. 213/07, Articles 2.6.1.3. (check at intervals not greater than seven days), 2.6.1.12. (exhaust and fire protection to NFPA 96; an existing system may be approved), 2.6.1.13. (maintenance to NFPA 96) and 2.6.1.14. (manual operating instructions posted and in the fire safety plan), and Article 1.1.2.1. (records of what was done and when): ontario.ca/laws/regulation/070213
  • NFPA 96, Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations, adopted by reference in both codes above. The standard itself sets the inspection frequencies.

The code references in this guide were checked against e-Laws and the 2024 Building Code Compendium on 31 October 2026, and the Building Code articles re-checked on 8 November 2026. The dollar figures are NHFC planning bands from our own Ontario projects, not published prices — no authority publishes hood costs, and a quote against real drawings will always beat a range.

Common questions

How much does a commercial kitchen hood cost in Ontario?

For a single Type 1 cooking line in a restaurant, budget $50,000 to $95,000 for the whole installed package: the hood, welded duct to the roof, the exhaust fan, a make-up air unit, a UL 300 fire suppression system, structural support and the commissioning balance. The hood itself is the smallest part of that. These are NHFC planning bands from our own projects — no authority publishes hood prices the way municipalities publish permit fees.

Why is a kitchen hood so expensive?

Because almost none of the cost is the stainless box. Exhausting a commercial kitchen means welded grease duct routed to the roof, a fan sized to the hood, and an equal volume of tempered air brought back in by a second rooftop unit with its own gas and power. Add a suppression system engineered to your exact appliance positions, structural support for two rooftop units, roof penetrations, and a balance report, and the hood is perhaps a fifth of the number.

How much does a kitchen fire suppression system cost?

Budget $6,000 to $20,000 installed for a single cooking line, as an NHFC planning band. The cost follows the number of nozzles, which follows the number and position of appliances, so a six-appliance line costs more than a two-appliance line of the same length. Moving a fryer after installation means re-engineering the system, which is why the equipment layout should be final before the suppression contractor designs anything.

How often does a commercial kitchen hood have to be cleaned in Ontario?

There is no single interval in Ontario law. The Fire Code requires that hoods, ducts and filters subject to accumulations of combustible deposits be checked at intervals not greater than seven days, and cleaned if the accumulation creates a fire hazard. It then requires the system to be maintained in accordance with NFPA 96, which sets inspection frequencies according to how much and what you cook. Keep records: where the Fire Code requires a measure to be carried out, a record of what was done and when has to be made.

Can I keep the hood that is already in the space?

Sometimes, and it is worth real money. The Fire Code allows an existing exhaust or fire protection system to be approved. But it has to be the right type and long enough for the line you intend to cook, the duct has to be sound and clean, and the suppression system has to meet the current standard. A pre-UL 300 dry chemical system does not, and replacing it is a cost that often arrives after the lease is signed.

Does a kitchen hood need a building permit?

Yes. Commercial cooking equipment ventilation is Building Code work, designed and installed to NFPA 96, and it forms part of the mechanical drawings in the building permit application. The fire inspection of the completed system is also part of the chain that leads to occupancy, so the hood is both a permit item at the start and an inspection item at the end.

How much does make-up air cost for a commercial kitchen?

Budget $12,000 to $35,000 installed as an NHFC planning band, and treat it as a separate project from the hood. A make-up air unit is a second rooftop unit that heats and delivers replacement air, which means its own gas line, its own electrical feed, its own curb and its own structural check. Skipping it does not save money; it makes the hood fail to capture and the doors hard to open.

What is UL 300 and why does it matter?

It is the standard a wet chemical kitchen suppression system has to meet. Ontario's Building Code requires fire protection systems for commercial cooking equipment using vegetable oil or animal fat to conform to ANSI/CAN/UL/ULC 300 or ULC/ORD-C1254.6. Older dry chemical systems were designed for the cooking oils and appliances of an earlier era and do not comply, so finding one above an inherited cooking line means budgeting a replacement, not an inspection.

Free consultation

Want this applied to your actual space?

Bring the unit, the lease or just the concept. You will get a project review, a realistic timeline and a preliminary cost breakdown — at no cost, and an honest answer if it does not work as scoped.

Start Your Project

Free Consultation

Tell us what you want to build.

The first consultation is free. You get a project review, a realistic timeline and a preliminary cost breakdown — including an honest answer if the project does not work as scoped.

Mon – Fri, 9:00 a.m. – 5:00 p.m. · No obligation

Call usStart your project