Skip to content
← All case studies

Specialty Food Retail

Butcher Counter, Hot Table and Café in One Retail Unit

A retail unit with no drains, no gas and no grease interceptor became three food operations under one roof. Keeping raw meat and ready-to-eat apart decided the whole layout.

Location
Barrie, ON
Size
2,000 sq ft
Timeline
20 weeks, blueprint to open
Budget band
$380K–$470K
How the 20 weeks broke down
20 weeks total
  1. Discover & feasibility3 wks
  2. Design & permit5 wks
  3. Construction10 wks
  4. Commission & handover2 wks
View as table
PhaseWeeksShare
Discover & feasibility315%
Design & permit525%
Construction1050%
Commission & handover210%

20 wks

Blueprint to open

3

Operations, one submission

400A

New service, 3-phase

Two brothers with a wholesale meat background wanted their own retail shop. Not just a butcher counter — a butcher counter, a hot table selling cooked food at lunch, and a small espresso bar at the front. Their reasoning was sound: the meat case brings people in once a week, the hot table brings them in at noon, and the coffee gives them a reason to stand still long enough to buy something.

They had a 2,000 sq ft unit in a Barrie plaza, previously a phone and electronics shop. Clean, bright, good frontage, and from a food perspective completely empty: no floor drains, no grease interceptor, no gas, 200A single-phase service, and a slab with nothing under it.

The challenge

This is the opposite problem to taking over a closed restaurant. There, the question is what you can keep. Here, nothing exists and everything is a decision.

Raw and ready-to-eat have to stay apart. This was the one that set the layout. A butcher operation handles raw meat. A hot table serves food ready to eat. A café handles open cups and pastry. Those cannot share prep surfaces, sinks, staff flow or storage, and a health unit will look specifically at whether they do. On 2,000 sq ft, with one back door and one service corridor, keeping three operations genuinely separate while still letting four people work a lunch rush is a layout problem with a small number of workable answers.

Nothing was plumbed. A butcher prep room needs a floor drain and a sloped floor. The hot table needs a hand sink within reach of the line. The café needs its own hand sink and a dump sink. The warewashing area needs a three-compartment sink and a dishwasher with hot water that actually sanitizes. None of that existed, which meant cutting the slab, running new sanitary, and finding somewhere to put a grease interceptor — sized for the hot table and the warewashing, with access for pumping, in a unit with no mechanical room and a landlord with opinions about the loading area.

Services were undersized. Meat saws, a grinder, a vacuum packer, a service case, two walk-ins and the refrigeration for the display line do not run on 200A single-phase. The service went to 400A three-phase. There was no gas at the unit at all, so a new service and meter had to be brought in for the hot table line and the bake-off oven.

Change of use. Retail to a food premises with seating is a different occupancy, and that pulls in washroom fixture counts, exiting and barrier-free requirements. The brothers had budgeted for a kitchen. They had not budgeted for a second washroom.

What NHFC did

Discover. Three weeks. We put the change of use through first, because it determines washrooms, exiting and accessibility, and those are walls — they cannot be value-engineered later. Then the two things with the longest lead times and the least flexibility: where the interceptor could physically go and be serviced, and what the utility would do about a new gas service to that unit.

Both came back workable, which is not always the answer. We have told operators to walk away from a unit over an interceptor. The honest version of the discover stage includes that outcome.

We also pushed back on the concept once. The original plan had the hot table cooking raw chicken on the line at the front of the store. Moving that production to the back prep area and keeping the front as holding and service only simplified the ventilation, shortened the hood, and kept the front-of-house smell closer to coffee than to a fryer.

Design. The layout came out as three zones on one axis: butcher prep and walk-ins at the back, production and warewashing in the middle, retail counter, hot table service and café at the front. Staff flow runs back to front and does not cross. Raw meat never enters the middle zone’s ready-to-eat surfaces, and the two sides have their own handwash and their own sanitizing.

Norpex specified the service case, the meat display line, the two walk-ins and the hot table holding units against that layout before the drawings were finished, so the case lengths, drain positions and circuit counts were real numbers rather than allowances.

One coordinated set went in: architectural with the change of use and the new washroom, structural for the slab work, mechanical for the Type 1 hood over the production line and the make-up air, plumbing for the new sanitary, interceptor and fixtures, electrical for the 400A three-phase service, and the refrigeration layout. Simcoe Muskoka District Health Unit reviewed the butcher operation, the hot table and the café in one submission, assessed separately.

Build. Ten weeks. Slab cutting and new sanitary first, with trench and area drains in the prep room and a sloped pour, then the interceptor set with its access. The 400A three-phase service and the new gas service were both utility-dependent, so they were ordered in week one of construction and tracked weekly.

Shop Flooring supplied a resinous system through the prep and production zones — washdown and thermal shock rather than foot traffic — and a sealed finish in the retail area. Partition framing, the second washroom, the hood and make-up air, refrigeration piping and the case set followed.

Deliver. Refrigeration pulled down and temperature-logged across the cases and both walk-ins before product. Hood exhaust and make-up air balanced against the appliance line. ESA cleared the new service and distribution, TSSA cleared the gas to the hot table and bake-off, and the health unit signed off all three operations at the pre-opening inspection.

The outcome

Twenty weeks, open, at roughly $215 per square foot. For a first-generation retail conversion carrying three food operations, a new sanitary system, a new gas service and a service upgrade, that is a reasonable number — and it is well over double what the same square footage costs in a second-generation space, which is exactly the trade they chose when they picked the unit.

The three-counter model worked. Lunch carried the weekday middle of the day, the meat case carried Thursday through Saturday, and the espresso bar did what it was there to do.

Scope at a glance

  • Change of use review ahead of design: occupancy, washroom counts, exiting, barrier-free
  • Grease interceptor sizing, siting and service access confirmed before lease commitment
  • New gas service and meter coordinated with the utility
  • Raw and ready-to-eat separation driving a three-zone layout with non-crossing staff flow
  • 400A three-phase service upgrade and distribution
  • Slab cutting, new sanitary, trench and area drains, sloped pour in prep areas
  • Second washroom built to barrier-free requirements
  • Type 1 hood and make-up air over a relocated production line
  • Butcher prep room: dedicated handwash, sanitizing sink, washable finishes, floor drain
  • Service meat case, display line, two walk-ins and hot table holding specification
  • Resinous flooring through prep and production, sealed finish in retail
  • Building permit, ESA, TSSA and Simcoe Muskoka District Health Unit plan review
  • Refrigeration temperature verification and hood balancing before opening

Free Consultation

Tell us what you want to build.

The first consultation is free. You get a project review, a realistic timeline and a preliminary cost breakdown — including an honest answer if the project does not work as scoped.

Mon – Fri, 9:00 a.m. – 5:00 p.m. · No obligation

Call usStart your project